Release note
German
IMPORTANT please read:
Consult the "History note read," for already implemented functions. If problems occur after the update, do a factory reset with the menu item "Install / Basic settings / factory settings by".
Please save your settings before the factory reset -> Menu / Software Manager / System backup
To perform a software update:
1st Unzip the file on a USB disk.
2nd Now connect the USB device with the receiver,
3rd On the receiver you choose from the menu / multimedia / media / USB, the update file *. dlp "from USB disk
4th Confirm the question with "Yes"
5th The update is complete when the receiver restarts.

08/07/2010  

Improvements:
- System Backup now saves the settings for Tuner2
- Fixed problems when copying files over 5GB
- Hard drive detection has been improved
- Channel logos are now displayed for the favorites.
o The logos are from the main channel list is automatically selected.
- Fixed Teletext on ZDF
- When starting the recording, the red line is displayed immediately. It has no buttons are pressed.
- When loading AVI's now a message is displayed.
- Timer recording start now if you look at a movie from the disk.
Yours sincerely,
Your VANTAGE - Support

Verbesserungen:

- Aufnahme Bugfix

o Fehler wie Bild- und Tonaussetzer sind behoben. Dies gillt nur fьr Aufnahmen die mit der neuen Software gemacht werden. Die Дnderung hat keinen Einfluss auf die bereits gemachten Aufnahmen

- Kanallisten Update

o ARD und ZDF HD auf den ersten beiden Plдtzen
Mit freundlichen

- Unicable background recording
o The receiver will start the timer in the background now and no longer switches to
- Added fast boats.
o enable this option through the boot process is accelerated (Note: The standby power consumption increases by!)
- Umlauts are now displayed in the player and the timer recording properly.
- Added option to turn off the system messages
- Quality of thumbnails in JPG's improved
- SD output option in the Video menu settings
o To: Scart connection has always picture.
o car: when a HDMI cable is plugged in, turned off, the Scart connector. This makes the box faster to use. Affects mainly for Linux.
- Timer standby circuit added.
o If the box is already in use when starting a timer to stop this even after the timer (even if the option to Standby "is placed). If the speaker is started by the timer turns them off, as in the standby field selected. This option will not be activated.

Zitat:

Improvements:

- Unicable background recording
o The receiver will start the timer in the background now and no longer switches to
- Added fast boats.
o enable this option through the boot process is accelerated (Note: The power consumption in standby rises
in fact! )
- Umlauts are now displayed in the player and the timer recording properly.
- Added option to turn off the system messages
- Quality of thumbnails in JPG's improved
- SD output option in the Video menu settings
o To: Scart connection has always picture.
o car: when a HDMI cable is plugged in, turned off, the Scart connector. This makes the box more quickly in
operation. Does especially in Linux.
- Timer standby circuit added.
o If the box is already in use when starting a timer to stop this even after the timer (even if the
Standby option to "on" stands). If the speaker is started by the timer turns the elected as the standby box
from. This option will not be activated.
- Last Unicable control
o Following up the software deletes the current Unicable settings. In the menu, there are now only
Unicable the option "Off" or "on" by pressing the OK button. In the new window now, the IF frequency
eingegben be and the corresponding number from 0-7. If no number is correct is no reception
possible. After entering the frequency and the number, the signal is examined, the signal is on the cable is
the setting is stored.
- Added German channel list
o The new Sky HD channels were added to the list.
- Fix special characters
o There are again all the letters in the EPG display.

- Bugfix Unicable
o Following up the software deletes the current Unicable settings. In the menu, there are now only the option Unicable "Off" or "on" by pressing the OK button. In the new window now, the IF frequency eingegben and the corresponding number from 0-7. Should the number be correct no reception is possible. After entering the frequency and the number, the signal is examined, the signal is on the cable to the setting will be saved.
- Fixed display bug in the Sort menu

- das Update dauert ca. 20 Minuten. Die Kanalliste wird beim ersten mal ьbernommen, danach sind die beiden Kanallisten getrennt voneinander zu bearbeiten. Um eventuellen Problemen vorzubeugen sichern Sie Ihre Kanalliste vorher auf den USB Stick.
Wichtige Hinweise:
- Дnderung der Fernbedienungstasten
o Ton aus ( 3 ) => VANTAGE Portal Seite
o Swap ( 33 ) => Ton aus
o Swap ist nun auf der PIP Taste. 1mal drьcken = PIP, 2mal drьcken SWAP
Дnderungen zum RTOS:
- HbbTV wird unterstьtzt
o Sobald die Netzwerkeinstellungen korrekt sind und sie auf einen Kanal mit HbbTV schalten wird rechts unten der rote Knopf eingeblendet, Durch drьcken der IP Taste kann dann HbbTV aufgerufen werden. Fьr die Funktionen innerhalb der HbbTV Seite sind die Sender verantwortlich, Sollten deshalb einige Punkte nicht anwдhlbar sein oder das Anwдhlen keine Reaktion zeigen ist dies auf eine unvollstдndige HbbTV Seite zurьckzufьhren und nicht auf den Receiver.
- Webradio
o Die Funktion kann durch drьcken der gelben Taste aktiviert werden. Nach einmaligem Aufrufen des Webradios kann die Textdatei auf dem Speichermedium mit weiteren Streams bearbeitet werden. Bitte hierzu nur vollwertige Texteditoren verwenden, Bei falschen Eintragungen kann es zu Abstьrzen kommen. Es werden nur m3u Streams erkannt.
- Playlisten kцnnen erstellt werden
o Die Playliste wird im Media Player direkt erstellt.
o Die Anzahl der Files pro Playliste ist auf 256 begrenzt. Die Anzahl der Playlisten ist nicht begrenzt.
- FTP Server:
o Die Zugangsdaten zum FTP Server bei Linux sind:
 Benutzer. vt1
 Passwort : vantage
- USB Wlan
o Die WLan Konfiguration wird im Menь Netzwerk vorgenommen. Die dazu benцtigten Tasten kцnnen ьber die Help Funktion eingesehen werden.

MPORTANT, please read:
If you experience problems after the update, do a factory reset with the menu item "Installation / Preferences / Factory Settings ".
Please backup before the factory reset your settings -> Menu / Software Manager / Windows system.
To perform a software update:
1. Start RTOS
2. Unzip the file on a USB disk.
3. Now connect the USB device to the receiver,
4. The receiver then from the menu / multimedia / media / USB update the file "*. lix" from USB disk
5. Confirm the question with "Yes"
6. The update is complete when the receiver restarts.
24/02/2011 Version 02.09ML-O BETA1
Getting started
- The update takes about 20 minutes. The channel list is included for the first time, then edit the channel list separately. To avoid possible problems, back up your settings before on the USB stick.
Changes:
- Improving the image distortion on HD channels
Yours sincerely,
Your VANTAGE - Linux Support